First knitting project
Knit a mug cosy and coaster
Forget a scarf that takes all November. Let’s start with a little coaster for your favourite mug. Every row uses just the knit stitch. Then use the same garter stitch to knit a cosy that fits your mug, with a button and loop beside the handle.
Jump to the steps Jump to the cosy
What you’ll need
- Smooth medium-weight cotton yarn. A light solid colour makes it easier to see your stitches.
- Two needles in the size suggested on the yarn label. Many medium-weight yarns work with 3.5–4 mm needles.
- Scissors, a tape measure and a blunt yarn needle for the ends.
- A flat button, sewing needle and strong thread for the cosy.
Part 1. Knit the coaster
- Cast on. Try 20 stitches to start. To make a simple knitted cast-on, knit into the end stitch without taking it off the left needle, then place the new loop onto that needle. Repeat, starting from a slip knot counted as your first stitch. Keep the loops loose.
- Knit the first row. With the yarn behind the needles, insert the right needle through the front of the stitch from left to right, wrap the yarn, draw a new loop through and slide the old stitch off the left needle. Work to the end.
- Turn and do it again. Knit every stitch in every row. This is garter stitch: it makes ridges on both sides. After a few rows, lay your knitting flat and measure the width without stretching. Aim for about 9–11 cm (3½–4¼ in) across. If it’s far off, this is a good time to cast on again with a different stitch count.
- Stop when it’s square. Compare the height and width. To bind off, knit two stitches and lift the first over the second. Knit the next stitch and repeat. Keep the edge loose enough to lie flat.
- Weave in the ends. Leave about 12 cm (5 in) of yarn, pull it through the last loop and use a blunt yarn needle to weave both ends into the ridges. Check that an empty mug sits flat. This is a coaster, not a potholder. Fancy trying sewing? Make a fabric bookmark
Part 2. Knit the mug cosy
- Measure an empty mug. Hold the tape against the mug on one side of the handle and wrap it around to the other side. Leave a small gap between the ends so the handle is easy to grip. Measure the straight section below the handle or between its attachments, too. A strip about 4–6 cm (1½–2¼ in) high often works, but it must sit below the drinking rim.
- Use the coaster to check your stitch count. The width of the knitting becomes the height of the cosy; each row adds length around the mug. Divide the number of stitches in your finished coaster by its width, then multiply by the desired height of the strip. Round to a whole stitch. For example, 20 stitches over 10 cm gives 10 stitches for a 5 cm strip.
- Knit a flat strip. Cast on the number you worked out and knit every row, just as you did for the coaster. When the strip is nearly as long as your wrap measurement, check it against the empty, cool mug. The ends should sit on either side of the handle without covering it. Bind off loosely and weave in the ends.
- Sew on a button and make a loop. Sew a flat button securely near the middle of one short end. For the opposite end, fold yarn double or make a short braid. Check the length before securing it: the loop should fit around the button, leave the handle easy to grip, and stay on with a gentle tug. Stitch the loop ends in firmly and weave them in.
- Check the fit on the empty mug. The cosy should stay in place, the button should not get in the way, and the base and rim should stay clear. If the strip slips on a tapered mug, try one with straighter sides. The cosy is decorative, not a potholder. Take it off before microwaving or washing the mug.






